Aprilia Rs 125 Service Manual Free Download
FUEL DANGER Fuel used to drive internal combustion engines is highly inflammable and may become explosive under certain conditions. It is best to refuel and carry out maintenance in well ventilated places with the engine switched off.
Do not smoke during refuelling or near fuel fumes. Avoid all contact with naked flames, sparks, or any other source that may cause ignition or explosion. Also avoid allowing the fuel to spill out of the filler cap as it could catch fire on contact with the very hot surfaces on the engine. Should fuel be spilled accidentally check that the area is completely dry before starting up the vehicle. The fuel expands when subjected to heat or the sun’s rays.
The fuel tank should therefore never be filled to the brim. Close the filler cap carefully on completing refuelling. Avoid the fuel coming into contact with your skin, inhaling vapours, ingestion and siphoning from one container to another using a hose. DO NOT DISPOSE OF THE FUEL INTO THE ENVIRONMENT.
KEEP AWAY FROM CHILDREN. Only use super lead-free petrol, with a minimum octane rating of 95 (N.O.R.M.) and 85 (N.O.M.M.). LUBRICANTS DANGER Adequate lubrication of the vehicle is essential to guarantee the safety of the vehicle. Failure to keep lubricants at sufficiently high levels or the use of inadequate, new and clean lubricants may cause the engine or gearbox to seize, resulting in accidents, serious injury or death. Gearbox oil may cause serious harm to your skin if handled for long periods of time and on a daily ba- sis. We recommend washing your hands carefully after having handled this oil. Do not dispose of the oil into the environment.
Deliver this oil to the nearest collection company for spent oil or the supplier, or have them collect it. WARNING When putting oil into the vehicle be very careful not to spill any. Immediately clean off any spilt oil, otherwise it may damage the paintwork on the vehicle. In addition, any oil that ends up on the tyres will make them extremely slippery, creating a dangerous situation.
Aprilia Rs125 Rs 125 2006 Workshop Service Repair Manual Free Download Summary: File 51,38MB Aprilia Rs125 Rs 125 2006 Workshop Service Repair Manual Free Download. Aprilia Rs 125 1993 2000 Factory Service. - Coulson And Richardson Volume 1 Solution Manual. - Countering The Conspiracy To Destroy Black Boy Free Pdf Download.
If an oil leak should arise, do not use the vehicle. Check and identify the cause of the leak and repair the component involved. ENGINE OIL DANGER Engine oil may cause serious harm to your skin if handled for long periods of time and on a daily ba- sis. We recommend washing your hands carefully after having handled this oil. Do not dispose of the oil into the environment.
Deliver this oil to the nearest collection company for spent oil or the supplier, or have them collect it. When carrying out maintenance we recommend wearing latex gloves. FORK OIL DANGER Adjusting the setting on the shock absorbers and/or the viscosity of the oil used in them may partially change the reaction of the suspension. Standard oil viscosity: SAE 20 W. The viscosity grade may be chosen in relation to the type of set-up you want on the vehicle (SAE 5W soft, 20W rigid).
These two products may be used in varying percentages in order to obtain the required reaction Incoming search terms: •. Disassembly forkleg 12_062 12_079Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 5 Frontfork 4357/4860 MXMA 02/2002 Clamp the forkleg (axle-clamp) in the vice and let the outer-tube down. Pull the spring downwards and place open-end spanner (size 22) on the hydraulic stop.
Audio Hijack Pro Core Keygen Mac on this page. Unscrew the screw-cap. 12_067 12_068 12_069 12_072Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 6 Frontfork 4357/4860 MXMA 02/2002 Remove the screw-cap from the piston- rod. 12_070 Remove the preload spacers. 12_074 Pull the spring downwards and remove the spanner.
12_075Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 7 Frontfork 4357/4860 MXMA 02/2002 Remove the spring. 12_076 Remove the adjustment tube with the O-ring. 12_089 Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 8 Frontfork 4357/4860 MXMA 02/2002 Clamp the axle-clamp in the vice so that the forkleg is at an angle of ±45 degrees. 12_095 Unscrew the compression holder out of the axle-clamp. (size 19) (when the cartridge is rotating with the holder, bend the piston- rod a little bit to the side) 12_096 Drain the oil out the forkleg. 12_094 Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 9 Frontfork 4357/4860 MXMA 02/2002 Remove holder compression.
Caution: oil iscoming out the cartridge. Disassemble the cartridge out the forkleg. 12_097 12_098 12_099 Disassemble the dust-wiper Incoming search terms: • • • •. Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1.
Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5.
Spacer (3) (keep) 6. Torx screw (5) (replace) 7.
Brake disc (keep) 8. Wheel assembly (replace) 9.
Valve cap (keep) 10. Compensator bowl (keep) 11.
Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse.
Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual.
Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. Install the new wheel to the rear fork.
Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2.
See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws.
Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover.
After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury.
(00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84 Incoming search terms: • • • • • • • • •. Cover the throttle bodies to prevent anything from dropping into the engine.
Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3.
Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4.
Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation.
Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft)!
Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation.!
Cover the throttle bodies to prevent anything from dropping into the engine. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3.
Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.
Incoming search terms: • • • • • • • • • •. REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding.
Disconnect battery cables, negative (-) battery cable first. Remove seat according to the instructions in the service manual. Refer to service manual to remove left saddlebag and side cover.
When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1.
Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual.
Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. Remove engine from chassis following the instructions in the service manual. Disassemble engine top end and bottom end.
Refer to appropriate ENGINE sections in service manual. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1.
O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in.
(2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2.
Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). Remove cylinder studs from the engine crankcase. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas.
Inspect and clean engine case mating surfaces. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm).
See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase Incoming search terms: • • • • • • • • • •.
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer. Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2).
◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug.
CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket.
Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid.
CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1 27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid.
WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer.
The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations), page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE).
Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end.
◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced. MACHINES Aprilia RS 125 production models, as produced from 01-11-05 and available in the UK via IN Competition from 01-01-06. (any parts exclusive to the older models including the pre-1999 SP model are not permitted to be used on machines in this series). The only eligible models are designated as Euro 2 & Euro 3 New machines are supplied with race kits included through: IN Competition Unit 1 New Lane Burscough Lancs 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg, this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg.
NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT RED background with WHITE numbers – Nitro Newcomers Class BLACK background with WHITE numbers – Aprilia Championship Class REAR BLACK background with WHITE numbers – Both Classes Placed in accordance with the ACU regulations. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed.
Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine.
Throttle must be standard, quick action throttles are not permitted. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. E85 Bio Fuel is also permitted when purchased from normal roadside outlets. FRAME BODY AND REAR SUBFRAME Frame must remain as originally produced by the manufacturer and may not be painted. The sides of the frame body may be covered by a protective part made of composite material of the original frame colour. Nothing can be added by welding or removed by machining from the frame body.
Engine mounting brackets or plates must remain as originally produced by the manufacturer. Bolt on accessories to the rear sub-frame may be removed. FRONT FORKS Forks structure (spindle, stanchions, bridges, stem etc) must remain as originally produced by the manufacturer. Standard original internal parts of the forks may be modified. After market damper kits or valves may be installed. The fork caps can be modified or changed to add spring preload/compression and damping adjusters.
Dust seals can be modified, changed or removed providing the fork remains totally oil sealed. Any quantity or quality of oil can be used in the front forks.
The height and position of the front fork in relation to the fork crowns is free. A steering damper may be added but may not act as a steering lock device. REAR FORK (Swing Arm). INSTALLATION 1. Remove existing front wheel assembly.
Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap.
Or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. See Figure 2.
Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle.
• For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side.
• For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table.
Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. Awesome Kong You Shoot Your Eye. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers.
Refer to FRONT WHEEL in service manual. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner.
After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant Incoming search terms: •. Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury.
Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings.
Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter.
See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing.
Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation Incoming search terms: • • •. TM REPAIR MANUAL IN LOOSE-LEAF FORM STORING THE REPAIR MANUAL IN THE BINDER -Put the index into the binder.
-Put the front page of the repair manual (210×297 mm) into the transparent pocket provided for this purpose on the outside of the binder. -Put the spine label (170×45 mm) into the transparent pocket provided for this purpose on the spine of the binder. -Put the summary list of contents (150×297 mm) into the transparent pocket provided for this purpose on the inside of the binder or insert this page on the beginning of the manual. -Then insert the individual chapters of the manual between the sheets of the index according to the page number printed in the right bottom corner of each page.
Example: page no. 3-5 3 = chapter 3 5 = page 5 All pages with a page number that begins with the digit 3, for example, must be put under the index heading „Chapter 3″. -Index sheets that have not been marked with a certain chapter are for your personal convenience. T he respective headings can be entered in the list of contents.
Remove page (s) Replace by page (s) Insert page (s) after page 2-1 / 2-7 2-1C 2-7C to 2-9C 3-1 3-1C 4-1 to 4-14 4-1C to 4-13C 5-1 / 5-3 5-1C / 5-3C 5-6 to 5-8 5-6C to 5-8C 5-12 to 5-26 5-12C to 5-27C 6-1 / 6-4 6-1C / 6-4C 6-7 to 6-16 6-7C to 6-17C 7-1 to 7-2 7-1C to 7-2C 7-7 to 7-11 7-7C to 7-11C 8-1 to 8-13 8-1C to 8-21C 9-1 9-1C 9-10 to 9-13 9-10C to 9-16C 10-1 10-1C 10-8C to 10-11C 11-1 11-1C 11-11C to 11-13C Repair manual KTM 250-525 SX, MXC, EXC RACING Art.-No. 3206007 -E EXPLANATION – UPDATING Edition 01/2003 3.205.85-ERepair Manual 400/520 SX, MXC, EXC RACING Basic version Model year 2000 (Engine number with first digit “0″) 2/2000 3.210.01-EUpdating of Rep.Manual 3.205.85-E Model year 2001 (Engine number with first digit “1″) 1/2001 3.210.44-EUpdating of Rep.Manual 3.205.85-E Model year 2002 (Engine number with first digit “2″) Incoming search terms: • • • • • •.